Material
selection.

Boards, laminates, hardware, stone, flooring and paint — chosen with the samples physically in your hands, and matched to the wear each surface will actually take.

Walk-in wardrobe in an Ahmedabad home finished in veneer with branded soft-close hardware

Turnkey — Materials

A sample in the hand
beats a name in a quote.

Anybody can write ‘premium laminate’ on a quotation. In Ahmedabad we would rather put the chip in your hand, tell you the brand, the grade and the thickness, and let you decide with your fingertips.

Selection sessions happen at the studio with the real thing on the table — boards, laminates, veneers, hinge samples, channel samples, stone offcuts, tile pieces, paint drawdowns. You approve a selection sheet, and that sheet is what the factory and the site are held to.

  • Physical samples, not catalogues
  • Board grade fixed room by room
  • Finish matched to real wear
  • Hardware chosen on load rating
  • Signed selection sheet
  • Brand & grade named in the quote
Book a Sample Session

Scope

What gets specified,
down to the grade.

Nothing on this list is left as ‘as per site’. Every line carries a brand, a grade and a thickness before it reaches the purchase order.

  • BWR & MWR plywood for wet and dry carcasses
  • HDHMR & MDF for shutters, profiles & panelling
  • Laminate, acrylic, PU & veneer finish selection
  • Edge-banding thickness & colour matching
  • Hinges, channels, lift-ups & soft-close on rated load
  • Wardrobe internals, pull-outs & kitchen organisers
  • Quartz, granite & marble counters and vanities
  • Vitrified, wooden & natural-stone flooring
  • Paint systems, sheen levels & texture finishes
  • Adhesives, sealants & waterproofing chemicals
Crockery and utility unit specified in moisture-appropriate board with rated hardware

Judgement

The right material is
the one that survives you.

A finish is not good or bad in the abstract. It is good or bad for a particular surface, in a particular room, used by a particular family.

High-gloss acrylic on a kitchen shutter that four people open with wet hands is a decision you will regret by month three. BWR under a sink is not optional. A 40 kg-rated channel in a drawer that will hold steel vessels is arithmetic, not preference. We say all of this out loud, even when it is not what you hoped to hear.

  • Wet zones vs dry zones
  • Fingerprint & scratch reality
  • Drawer loads & vessel weight
  • Heat, humidity & west-sun exposure
  • Repairability years from now
  • Honest cost-versus-life advice
See Finishes in Place

Our Design Process

Eight stages. Zero surprises.

Material selection runs alongside design and closes before production — the last stage where a choice is still a choice and not a purchase order.

01

Consultation

Understanding your lifestyle, requirements and budget.

02

Budget & Approval

A detailed quotation with complete transparency — no hidden lines.

03

Design & Planning

Space planning, design concepts and photoreal 3D visualization.

04

Material Selection

Choosing premium finishes, hardware, colours and textures together.

05

Manufacturing

Precision-crafted modular furniture, plus coordinated on-site work.

06

Execution

Professional installation under dedicated site supervision.

07

Quality Check

A thorough inspection of every joint, finish and fitting before sign-off.

08

Handover

Delivering a beautifully finished space, ready to enjoy from day one.

Questions

Boards, finishes
and hardware.

The technical questions worth asking any studio before you sign — and the answers we give whether or not you end up working with us.

+91 88492 96750

BWR is boiling-water-proof plywood with a phenolic-bonded core — the grade we use for kitchen base units, utility areas and vanity carcasses. MWR is moisture-resistant, adequate for dry bedrooms and living rooms. HDHMR is a dense, uniform engineered board that stays flat and takes a routed profile cleanly, so it suits shutters and panelling. Plain MDF is the softest of the four and we restrict it to dry, low-load decorative work.

Laminate is the workhorse: hard-wearing, forgiving and available in hundreds of decors. Acrylic gives a high-gloss mirror face that shows fingerprints and needs care. PU is a sprayed paint finish, seamless and fully colour-matchable but repairable only by respraying. Veneer is real wood — the warmest and the most variable, because no two sheets are identical. We match the finish to the room, not to fashion.

Always. Nothing is purchased on the strength of a render or a catalogue photograph. You sit with the actual laminate chips, the veneer sheet, the hardware sample and the stone piece, under the light temperature your home will be lit at — and you sign the selection sheet before we raise a single order.

We specify from established brands — Hettich, Blum, Ebco and Hafele among them — and choose by rated load and tested cycle count, not by price. A soft-close hinge that has been through a hundred thousand cycles in a lab is the reason your wardrobe door still shuts quietly in year eight. Hardware is where cutting cost costs the most.

Quartz is engineered, non-porous and consistent slab to slab, which makes it the safer choice for a busy Indian kitchen with turmeric, lemon and hot vessels in play. Granite is natural, harder against heat, and will always carry some variation. Marble we recommend for vanities and low-traffic surfaces, not for a cooking counter.

More than most people expect. A matt emulsion hides a slightly uneven wall but marks easily, so it belongs on ceilings and quiet bedroom walls. A satin or soft-sheen finish wipes clean, which is why we use it in passages, kids’ rooms and anywhere small hands land. High gloss shows every imperfection in the plaster below it.

Related

Where the samples
end up.

All Turnkey Projects

Furniture Manufacturing

The approved selection sheet turned into cut, banded and assembled carcasses in our own unit.

Explore

3D Visualization

Your chosen finishes rendered as they will actually read under your lighting.

Explore

Modular Kitchens

The room that punishes a weak board grade fastest — and rewards a good one for a decade.

Explore

Site Supervision

Someone on site checking that what was specified is what actually arrived.

Explore

Associated Brands

The names we
build with.

Cores, hardware, laminates and finishes are specified from brands that stand behind their warranty — because the parts you never see decide how long the ones you do see keep looking right.

  • Hettich
  • Godrej
  • Blum
  • Häfele
  • Ebco
  • Grass
  • Greenply
  • CenturyPly
  • Action TESA
  • Merino
  • Virgo
  • Greenlam
  • Royale Touche
  • Advance Laminates

Start your project

Talk to a designer
about Material Selection.

Tell us a little about the space. A designer — not a call-centre — calls you back within one working day with straight answers on scope, timeline and cost.

  • A free first consultation
  • Photoreal 3D before anything is built
  • A line-by-line written quotation